Bench Dog Tools Phenolic ProPlates Bedienungshandbuch PDF herunterladen

Congratulations and thank you for buying our router

table! If you have any questions, please give us a

call. This manual will assist you during the assembly

of your router table. However, this manual is not

intended as an instructional manual for router table

usage. Please consult the widely available books,

magazines, and classes on router table techniques.

Thank you for choosing Bench Dog!

Owner's Manual

model number

RT100

Contents of Box

Tools Required

Router Table Hardware 

Fence Hardware/Accessories

2 3/8-16 x 3" carriage bolts for fence mounting

2 3/8" nylon handle spacer washers

2 2-1/2" t-bar knobs for fence mounting

2 1/4-20 x 3/4" hex bolts for bit guard mounting

6 1-1/8-1/4" knobs for sub-fence and guard mounting

4 1/4" x 40mm shoulder bolts for subfence mounting

1 dual position bit guard

1 dust port (slides into fence)

2 MDF subfences

2 aluminum knob spacers

2 aluminum jointer bars (pair)

12 1/4-20 x 2" round head bolts for cabinet and top

2 1/4-20 x 3/4" phil. flat head ms for insert plate

1 1/4-20 x 1" phil. flat head ms for miter track

2 1/4-20 x 2" phil. flat head ms for miter track

14 1/4-20" cross dowels for cabinet and top

12 7 x 40 mm insert plate leveling screws

10 1/4-28 x 1/2" set screws for miter track

2 Euro hinges and mounting plates with screws

1 door stop with (1) #7 x3/4" screw

1 nylon handle with (2) #8 x 1-1/8" screws

2 aluminum trim strips for routertop

4 #6 x 1/2" screws for trim strips

Cabinet Panels

1 left side panel

1 back panel with cord cut-out

1 right side panel

1 base panel

1 door panel

1 routertop

1 fence

1 phenolic ProPlate, standard 2" bit hole (router insert plate)

1 miter track

Symbols

Warning

Assembly

Mounting Router

Important

4 mm Allen wrench (supplied)

1/8" Allen wrench (supplied)

screwdriver and power drill

drill bit (sized to your router)

countersink 82 degree

drill press (recommended)

612.782.8205 main

612.788.2518 fax

800.786.8902 toll free

[email protected]

www.benchdog.com

Bench Dog, Inc.

3310 5th St. NE

Suite 100

Minneapolis, MN 55418

Be sure to check out our web site for all the

latest and greatest accessories and tools.

www.benchdog.com

1-800-786-8902

Read and understand the entire contents

of this manual before attempting assembly

or operation of this tool! Inspect contents

for shipping damage and shortages. Report

problems directly to Bench Dog, Inc.

QUESTIONS?

82-0007-01 1102

2002 Bench Dog, Inc.

1 2 3 4 5 6 ... 10 11

Inhaltsverzeichnis

Seite 1 - 1-800-786-8902

Congratulations and thank you for buying our router table! If you have any questions, please give us a call. This manual will assist you duri

Seite 2 - Important Safety Points

Page 10Dust CollectionStockNot a trap.Correct feed direction!Fencebit rotationFenceClassic Trap!StockIncorrect feed direction!NO!bit rotationUsing You

Seite 3 - Door stop detail

Bench Dog Accessories Please contact us if you have any questions (1-800-786-8902). Be sure to check out our web site for all the latest accessories a

Seite 4

General Conditions and Limited Two Year WarrantyImportant Safety PointsBefore operating your router table please read this manual thoroughly.

Seite 5

Page 3Assembly Instructions1. Attach the Euro hinges to the door as shown. Press the hinge cups into their bores. Turn the integral hinge cams to tigh

Seite 6 - 1/4-20 x 40mm

Page 45. Attach the cabinet base panel. Flip the cabinet over, as shown. Use the same 1/4" round head bolts and cross dowels as above. When done,

Seite 7 - Basic Operations

Page 510. Adjust the miter gauge track to fit your miter gauge.Begin this step by first test fitting your miter gauge for fit. If it fits too tightly,

Seite 8 - Jointing

Page 614. Install the dust port. Pull the port along the two grooves extruded into the fence until it snaps into place in the center bit openin

Seite 9 - Adjusting the Subfences

Page 717. Attach the dual position bit guard to the fence.Use the (2) 1/4-20 x 3/4" hex bolts and knobs. The bolt heads slide into the t-slots on

Seite 10 - Temperature Regulation

Page 8jointer barsHere, the jointer bars aremounted in slots 2 and 4.Always use a push stick or pad when jointing!Note the small "v" grooves

Seite 11 - Bench Dog Accessories

Page 9Adjusting the Subfences 1. Set the bit height and fence where you need them. Confirm that the bit, router, insert hold- down screws and fence